Remember also that unless you hit the Record button on (These adaptors are available for <$5 from Radio Mono audio from your camcorder into BOTH of the audio Left (white) is the traditional default when you have only a They want you to use the back one, they should SAY SO. I put the jack in the hole on the front of the converter. I just went eeny, meeny, miney, moe, and chose the red one (Audio in-R)Īs it's closest to the yellow one (Video-which I didn't connectīecause of the vague but seemingly dire threat at the side of the In the audio jack only-there is only ONE audio jack (on the camera)īut TWO audio holes (on the converter), and they don't give you a CLUEĪs to which one (if either) is correct, (if it makes any difference) so Into empty air without a connection deserves what they get) I plugged How-now I guess they figure anyone stupid enough to play the audio Instructions say are, "Play the audio data to capture"-not a THINGĪbout connecting it to the converter AT ALL, let alone where or Titles), and since they don't give a CLUE as to connections (ALL the Well, since all I wanted was the audio anyhow (as the video will be the Mode, the subsequent operations can not be guaranteed." Says, "Caution: If video signal is input during the Audio Capturing
#Canopus advc110 video converter manual
A sidebar on the Audio Capturing mode page in the manual I'd also like to know if I had the camera connected correctly to theĬonverter. That was what I wanted, a different way to try it before I Then end the capture after the part you want. Start the tape playing, and then start the capture. Wind the tape to ~15 seconds before the part you want to capture. Going until AFTER what I want, then switch everything back? Would that Playing it, then do all the switching on the converter, keep the tape Mean I should wind the tape back to BEFORE the part I want, start Only the part I wanted to capture, and stopped it again. Point of view is 'PLAY.'" I've had the camera stopped, then played Point, and was stopped at this part every time: "Note: Switch to theĪudio Capturing mode, only when the Deck Status from the application's I was able to follow the instructions in the manual up to a I have no clue what this means, let alone how It is stating the obvious.if you stop the tape it can't capture. Stop the tape? Am I supposed to play the whole tape to get the 15 Sorry to be stupid, but how exactly am I to get what I want if I DON'T Reads: "When the input source is paused or stopped in the Audio Post by "Caution" in the sidebar of the "Audio Capturing mode" instructions Help there and I may not, so that's why I'm asking.Īnyone have one of these? And anyone specifically use it with iMovie? IĪlso wrote "sales" at the company regarding support. Registrations from any email addresses ending These are the only two I have! I wrote the webmasterĪbout this and if nothing else I suppose I can register under aįriend's email address and then have them send me the information. I went to their official site and tried joining their forums, The Desktop and I don't know where else to look for a file or whatever If the converterĪctually did anything, nothing new has shown up on the Hard Drive or To get it into iMovie if supposing I could find it. It says the data is supposed to be captured to myĬomputer, but gives no clue HOW or WHERE this is to occur, or HOW I am Instructions, all the right lights come on and everything goesįine.to a point. The equipment is connected, and when I follow (In this case, the music is from theĬamera, but it doesn't matter it can come from any source with the Titles and transport the whole thing (titles and music together) to myĬamera to add them to the video. I bought this high tech equipment in order to add music to the I created some titles in iMovie for a video I'm making.Ģ.
#Canopus advc110 video converter mac
Is iMovie strictly for Macintosh? Because I have a Mac and don't knowġ.
Anyone out there have one of these? Anyone used it with iMovie? (And,
0 kommentar(er)
